My line was finally activated on Thursday, but I am still not connected to the internet. I have a Draytek 130 and I cannot access its interface to connect it to my Asus router. I input the username and password provided by o2 directly on the Asus, but there is still no internet connectivity. I just hope I have the correct cables, I bought the Draytek used and I had to find a TAE cable with RJ11. Any help would be greatly appreciated!
Edit o2_Lars: Transfered to our english community.
+5
edited: what firmware you have on the daytrek 130?
I have the 100mbit, my username is s93
Moin Moin,
you have to enter the login parameter into your daytek.
Little help you could find her.
The VLAN ID could be enter in the router.
If you really have a RJ11 you could use this one. If you have really a RJ11 connector than you have the Annex A version.
For help take a look her…
For Firmware Update look her should be 3.8.4.1
The combination is not the easiest combination if you do not know much about router, XDSL modem and the necessary parameters for German DSL access ...
What really baffles me is not being able to access the modem’s interface. I only have an old laptop and I have tried connecting it with the RJ45 cable provider by Asus. Its clips seem quite long compared to some standard yellowish Ethernet cables. It clicks on my laptop l, but is it possible that it doesn’t fit with the modem? I also bought a TAE cable with RJ11 and that looks like it fits properly with my plug and Draytek 130.
I have the Annex B version, but even If I got the wrong cable, should not I be able to access the modems interface?
+5
Yeah I did, twice.
+5
Either there is something wrong with the modem or the Ethernet cable I have us not compatible. That will teach me but used modems without cables in a country I am not familiar with their specific interface.
The vigor schloud have 192.168.1.1 as IP. User admin Password admin.
So you pc schloud have 192.168.1.2 as IP.
I tried 127.0.0.1 but it didn’t seem to work
I have the Asus ax58u
I tried to set it up in AP mode but that didn’t work. I have done that in the past but with modem/router as the backend device, I am not sure which mode I should choose for connecting the Asus to the Draytek.
This cabel [ https://www.amazon.de/ecabo-10061-Stecker-RJ45-Stecker-Anschlusskabel-Schwarz/dp/B071CJBJTV ] is a phone cabel not a DSL Cabel.
½ of the TAE should be 3 /4 on modem. If you have luck you can open the TAE plug.
With more luck you could change the position of ¾ to ½. Carefully pull the contact up to the crimp side than move out side than down. The contact has the from of J, the upper part of the J is the crimp side.
+5
I tried 127.0.0.1 but it didn’t seem to work
127.0.0.1 is your own PC! That’s a loopback address….
Wrong dsl cable…. It is a phone cable.
The DSL light is blinking
This cabel [ https://www.amazon.de/ecabo-10061-Stecker-RJ45-Stecker-Anschlusskabel-Schwarz/dp/B071CJBJTV ] is a phone cabel not a DSL Cabel.
½ of the TAE should be 3 /4 on modem. If you have luck you can open the TAE plug.
With more luck you could change the position of ¾ to ½. Carefully pull the contact up to the crimp side than move out side than down. The contact has the from of J, the upper part of the J is the crimp side.
Could someone direct me to the proper TAE cable? Ideally with next day Prime delivery. It is still weird that I cannot access the modem interface, maybe I need to order a new Ethernet cable too.
I tried 127.0.0.1 but it didn’t seem to work
127.0.0.1 is your own PC! That’s a loopback address….
I know, I tried 192.168.1.1 but then I tried to ping it with the loop back address (which is probably pointless)
This cabel [ https://www.amazon.de/ecabo-10061-Stecker-RJ45-Stecker-Anschlusskabel-Schwarz/dp/B071CJBJTV ] is a phone cabel not a DSL Cabel.
½ of the TAE should be 3 /4 on modem. If you have luck you can open the TAE plug.
With more luck you could change the position of ¾ to ½. Carefully pull the contact up to the crimp side than move out side than down. The contact has the from of J, the upper part of the J is the crimp side.
Could someone direct me to the proper TAE cable? Ideally with next day Prime delivery. It is still weird that I cannot access the modem interface, maybe I need to order a new Ethernet cable too.
I’m only used to work with Ethernet cables. The TAE i bought fit the telephone line plug, I assume that is where I get internet from too? I have another socket that says data and uses coaxial inputs, but that is for cable I assume which I was told by Vodafone is not available in my building.
+5
Why do I need an adapter?
would something like this work?
https://www.amazon.de/ecabo-10061-Stecker-RJ45-Stecker-Anschlusskabel-Schwarz/dp/B01NBIRER7
I think the TAE end of this is not matching the plug anyway, I ordered the TAE for Deutche Belegung, but that ends with RJ11 and you said that is a phone cable anyway.
The RJ11 to RJ45 cable you mentioned will take ages to reach me, should I get this instead in conjunction with the adapter?
https://www.amazon.de/ecabo-10105-Modularkabel-Telefonkabel-Anschlusskabel-Schwarz/dp/B07L28673Y
Also, I think I need to order an Ethernet cable too, I have an RJ45 to RJ45 from Asus, I tried connecting the router to my old Dell laptop with no luck. My laptop should detect the Ethernet connection, so the browser would have connected me if I tried 192.168.2.1, wouldn’t it?
Enter your username or e-mail address. We'll send you an e-mail with instructions to reset your password.
